Comme des milliers de personnes, recevez gratuitement chaque semaine Correction/présentation orale
Cours gratuits > Forum > Forum anglais: Questions sur l'anglais || En basCorrection/présentation orale
Message de enis38 posté le 25-05-2016 à 12:34:04 (S | E | F)
Bonjour à toutes et à tous!
Voici ma présentation orale pour un entretien, j'aimerais avoir vos avis et une correction de mon anglais.
Toutes remarques sont bonnes à prendre pour moi, je vous remercie beaucoup de votre compréhension.
I had a Diploma in Electrical and Informatics Engineering in 2005 then I enchained on a pro license optronics and I started working at xxx or I was performing electrical tests on 900 kva inverters. Then I worked for xxx, I also was conducting tests but on electronic cards.
After that I was technical hot-liner at xxx I supported catalogs "Residential and small commercial" and "Electrical distribution and low voltage" where I helped customers either for purchase for commissioning or for troubleshooting. Then always for xxx, I worked in service of quality. I received a sample of contactor, I put on the test bench then I write the test report with the number of opening and closing and how the contactor burn.
I also tested the fuses (40A to 600A) dedicated to aeronautics climatic chamber (temperature range from -55 ° C to 125 ° C) and then I traced the melting curves and wrote the report.
The tools I used were multimeters, oscilloscopes, voltage, low frequency generators generators megohmmeters, test bench, climatic chambers and dielectric.
I was in xxx supplies quality service or compensation I managed customers .
Then I decided to return to school in aeronautics as I have always done the model and I was always fascinated by this domain. Since October 2015 I have a bachelor's degree in aviation maintenance for continuing airworthiness and have access to the part 66 C.
During my internship at xxx, I worked with mechanics and avionician to implement work tasks, I defined the applicabilities, the access time of interventions, supplies, skills and tools.
I worked with xxx (AMM, IPC, Zones) to help me but also with the world xxx site for new work tasks and service bulletins.
I have done complete all scheduled and non-scheduled maintenance planning and I check applicability of new tasks from xxx.
-------------------
Modifié par lucile83 le 25-05-2016 15:08
Message de enis38 posté le 25-05-2016 à 12:34:04 (S | E | F)
Bonjour à toutes et à tous!
Voici ma présentation orale pour un entretien, j'aimerais avoir vos avis et une correction de mon anglais.
Toutes remarques sont bonnes à prendre pour moi, je vous remercie beaucoup de votre compréhension.
I had a Diploma in Electrical and Informatics Engineering in 2005 then I enchained on a pro license optronics and I started working at xxx or I was performing electrical tests on 900 kva inverters. Then I worked for xxx, I also was conducting tests but on electronic cards.
After that I was technical hot-liner at xxx I supported catalogs "Residential and small commercial" and "Electrical distribution and low voltage" where I helped customers either for purchase for commissioning or for troubleshooting. Then always for xxx, I worked in service of quality. I received a sample of contactor, I put on the test bench then I write the test report with the number of opening and closing and how the contactor burn.
I also tested the fuses (40A to 600A) dedicated to aeronautics climatic chamber (temperature range from -55 ° C to 125 ° C) and then I traced the melting curves and wrote the report.
The tools I used were multimeters, oscilloscopes, voltage, low frequency generators generators megohmmeters, test bench, climatic chambers and dielectric.
I was in xxx supplies quality service or compensation I managed customers .
Then I decided to return to school in aeronautics as I have always done the model and I was always fascinated by this domain. Since October 2015 I have a bachelor's degree in aviation maintenance for continuing airworthiness and have access to the part 66 C.
During my internship at xxx, I worked with mechanics and avionician to implement work tasks, I defined the applicabilities, the access time of interventions, supplies, skills and tools.
I worked with xxx (AMM, IPC, Zones) to help me but also with the world xxx site for new work tasks and service bulletins.
I have done complete all scheduled and non-scheduled maintenance planning and I check applicability of new tasks from xxx.
-------------------
Modifié par lucile83 le 25-05-2016 15:08
Cours gratuits > Forum > Forum anglais: Questions sur l'anglais
INDISPENSABLES : 